Copper Wire Vertical Enamelling Machine

• Customization: Available
• After-sales Service: Afersale Serive
• Driven Type: Electric
• Model NO.: ZHY001
• Condition: New
• Warranty: 12 Months
• Screw: Single-Screw
• Product Wire Size: 0.7~2.5mm
• Wire Lines Qty: 6
• Line Spacing: 11.5mm
• Height: 1000mm
• Specification: Customization
• Trademark: zhenhuan
• Origin: Cn

Product Description

1.Technical Requirement
 

No.	Term	Data
1	Power supply	415V×50HZ×3 phase
2	Product wire size	0.70mm-2.50mm
3	Number of wire lines	6line
4	Passes of coating enamel	single coated 7passes
5	Line spacing	11.5mm
6	line height	1000 mm
7	Leading wire method	Wires are arranged lengthways, control 1strips of steel strip independently.
8	Weight of take up wires	PT25-PT60
9	The electric power required	About 220KW
10	Painting Color	annealer furnace and oven are painted silver pain to resists heat 350ºC.

:

1. Discharge supportPay

No.	Term	Data
1	Independent dismounting frame	rolling diswinding
2	Spacing between outings	800 mm
3	Guide wheel	150 alloy aluminum guide wheel diameter
4	Firing device	iron shaft discharger with diameter500Pay  off cover:30fliers for unwinding wire,  suitable forΦ500 iron spool.
5	The height of the paying off shelf	1500mm
6	the height of running wires	1600mm, side-standing type

3.Annealer furnace
    

No	Term	Data
1	Size: Length	11000mm
2	26annealer pipes size	25x2.0
3	material	SUS321
4	Annealer temperature	Heat by MAX550ºC tubular electric heating element .
5	Control mode	inlet, middle and outlet temperature control, thermocouple temperature measurement, heating part is controlled by the solid-state relay.
6	Exit part	Cooling with sink. The anneal entrance equipped with good quality bearing.
7	Blow the cooling water off the surface by hyperbaric ductwork after out of water.

     4.Enamel application method:

No.	Iterm	Information
1	Enamel trough	Felt painting method, install 7 felt clips
		(B)The materials used in the trough and pipe are stainless steel, feed circularly
		(C)Governor control motor speed
		(D)There is a 40W double daylight lamp above the enamel tank for lighting.
		(E)Install the dust cover device.
2	Enamel feeding system:	(A)The enamel circulate constantly through the feeing box to make enamel is plastered evenly. The whole tank body is stainless steel material.
		(B)Control the temperature with a electric heating thermostat
		(C)Equipped with float adjusting valve and Liquid Surface and Alarm System.
		(D)Equipped with Enamel Lacking Alarm System and overflow alarm system.

5.Oven: .

No.	Term	Data
1	Oven style	The heat energy can be used repeatedly
2	The oven size: length	7100mm
3	Temperature	The temperature of oven surface is below zero 60ºC. (In room below35ºC)
4	Strip line	stainless steel strip
5	heating mode	Heating pipe reaching 550 degree. The electricity capacitance can make the oven temperature up to 550ºC within 2hours.

6. Furnace temperature control: 

No.	Information
1	Heating part	inlet temperature, intermediate temperature, outlet temperature, pre-catalytic temperature.
2	Inlet temperature and outlet temperature	"S, C, R" PID control, other relay PID control.
3	The distance from the sides of oven to the edges	40 mm
4	Cooling	Outlet installation air curtain cooling system.

7.Catalytic combustion:
 Dual catalyst system adopted by the oven, the oven, the  
  all metal catalytic plate provide high efficiency burning and allow the     
  exhaust value fit for the national standard.

1. Cold Air:Install independent air fan at inlet and outlet to block incoming cold air;

 

1. Exhaust system : The exhaust system regulated by the electromechanical

 
10.Haulage drum:
      * A stand-alone speed control on the left and right, Φ300mm, the outer chrome plated surface, the run out of the top circle is below 0.05mm.
* Motor inverter control, digital display, mounting flat belt.
* The roller is installed in the receiving section(1);

11.Take-up System:
Install 48 torque receiving motors and automatic wiring receiving system; install the maximum disk PT-60;